CCI

MBM6F-E3B

3 ft (1.0 m), single-band, 24-port multi-beam panel: six independent beams with 4x4 MIMO, or twelve with 2x2 MIMO, 1695–2690 MHz.

Antenna · Multi-Beam · Panel Multi-Beam Verified from manufacturer datasheet
Manufacturer PDF

Public datasheet summary. The specifications on this page are taken from CCI’s publicly available datasheet, linked above. CCI owns its name, trademarks and specifications, which may change without notice. This site is not affiliated with, endorsed by, or sponsored by CCI, and nothing here is proprietary to this site. Values are provided as-is for reference only — the manufacturer’s current datasheet is the authoritative source.

Six independent beams with 4x4 MIMO (24 ports, 4 per beam) or twelve beams with 2x2 MIMO (2 ports per beam). Beam 1 is the leftmost beam and Beam 6 the rightmost, as drawn in the datasheet's azimuth plots; the azimuths in the Beams section are read from those plots (approximate, ±3°) — the datasheet publishes no per-beam azimuth table, and the mRFSafe list carries only a 0° panel offset for this model. Front-to-back ratio published as a minimum ('> N dB'); recorded as the plain number. The 6-beam 4x4 MIMO configuration is listed, with the shared per-sub-band specs in Coverage. Ordering part MBM6F-E3BA-K (fixed electrical tilt, 4.3-10 connectors, MBK-10 brackets).

SPEC.COVCoverage5 band rows
Band, MHz Ports GainHorizontal BWVertical BWElectrical tilt PIM, dBc Power / port USLS, dB
1695–1880MHz 1-24 19.9dBiavg 19.7 11.2° 17.9° 7° fixed -153dBc 200W 20dB
1850–1995MHz 1-24 20.8dBiavg 20.5 10° 16° 7° fixed -153dBc 200W 17.7dB
1920–2180MHz 1-24 21dBiavg 21 9.4° 15.3° 7° fixed -153dBc 200W 15.5dB
2300–2400MHz 1-24 21.8dBiavg 21.9 7.9° 13.1° 7° fixed -153dBc 200W 12.4dB
2496–2690MHz 1-24 22.7dBiavg 22.9 6.9° 11.5° 7° fixed -150dBc 200W 13.6dB

Fixed electrical tilt 7°

SPEC.BEMBeams6 beams

One antenna, many beams. Each beam is an independent narrow sector with its own ports, so a single antenna can cover several directions at once — useful on stadiums, venues and dense sites, where it replaces several separate antennas.

All beams cover 1695–2690MHz.

Azimuth read from the datasheet's azimuth diagram (approximate). 4 ports per beam in the 4x4 MIMO configuration (24 ports total); per-beam port assignments are in the datasheet's connector diagram.

Beam Azimuth Electrical tilt
Beam 1 -45° 7° fixed
Beam 2 -25° 7° fixed
Beam 3 -8° 7° fixed
Beam 4 8° 7° fixed
Beam 5 25° 7° fixed
Beam 6 45° 7° fixed
SPEC.ELEElectrical
Polarization
±45°
VSWR
1.5: 1
PIM, 3rd order
By band, see Coverage
Max input power
By band, see Coverage200 W CW per port (datasheet 'Input Power Continuous Wave (CW) 200 watts' per sub-band column)
Impedance
50Ω
Isolation
>25 dB (cross-polar port-to-port); interbeam co-pol >15 dB, non-adjacent beams >12 dB
SPEC.MECMechanical
Dimensions
1017 x 1104 x 177mm
Weight
39.9kgexcludes mounting
Wind load
Front 1652 N, side 296 N at 100 mph (161 kph)
Max wind speed
>241 km/h (150 mph)
Connectors
24x 4.3-10 female
Port count
24
Mounting
MBK-10 mounting bracket kit (top and bottom), 0°–10° mechanical tilt adjustment; mounting pole 2–5 in (5–12 cm), pole spacing 31.5 in (800 mm)
SPEC.PRTPorts24 total
  • Ports 1-24 1695–2690MHz
1+2−3+4−5+6−7+8−9+10−11+12−13+14−15+16−17+18−19+20−21+22−23+24−
Illustrative port layout — drawn from the published 24 ports and ±45° polarization. The arrangement is schematic; the exact positions are in the manufacturer PDF.
  • Ports 1–241695–2690MHz
SPEC.PATRadiation patterns5 bands
0°90°180°270°All beams · 6 azimuths
All beams — horizontal · 6 distinct azimuths · lobe widths from the 1930 MHz band (HBW 10°) — per-beam widths are published per sub-band, not per beam
0°90°180°270°HBW 11.2°
Horizontal — 1695–1880MHz
0°90°180°270°VBW 17.9°tilt 7°
Vertical — 1695–1880MHz

Illustrative patterns — the main lobe is drawn on a 0 to −30 dB scale so its −3 dB width matches the published beamwidth. The back lobe, where shown, sits at the published front-to-back ratio. Sidelobes are not drawn. The exact plots are in the manufacturer PDF.

CALC.EIRPUse this gainEIRP / ERP

Pick a band. The gain comes from the table above. Add your transmit power and feed loss to get EIRP.

EIRP — Turn on JavaScript, or use the calculator link.

EIRP = TX power − loss + gain (dBi). ERP = EIRP − 2.15 dB. Open the full EIRP calculator →

SOURCESource and corrections
Source
Manufacturer datasheet PDF, read 2026-11-16: https://www.cciproducts.com/DsPdf/ds-mbm6fe3b-v1_4-250620.pdf
Datasheet revision
Revision 1.4, 06/20/2025
Added

Specifications belong to CCI and can change without notice. The manufacturer’s current datasheet is the authority; check it before you sign a report. Everything on this page is public data — the same datasheet anyone can find with a Google search. Nothing here is proprietary. This site is not affiliated with, endorsed by, or sponsored by CCI. If you represent CCI and want a correction or removal, use “Report an error” below.

Report an error in these specs

Upload a newer datasheet revision